Industry dynamics-Zhenxing Grinding Wheel Co., Ltd.

Enterprise Information

Release time:

2023/04/03 23:08

◆ Simple maintenance. The dressing equipment of white corundum grinding wheel can be used instead of expensive dressing equipment. SG abrasive in order to maintain its cutting edge sharp, only requires less dressing, less dressing will get the grinding wheel life, compared with alumina grinding wheel, ceramic corundum abrasive grinding wheel dressing times can be reduced by 80%. It is a composite oxide of alumina and zirconia. This abrasive is grayish white, with high toughness, high strength and good wear resistance. In the rough grinding of steel, raw grinding and heavy load grinding, showing high grinding efficiency, good roughness, not easy to burn the workpiece.

What are the characteristics of the grinding wheel saw blade?

Release time:

2023/03/27 23:31

The specifications and dimensions of the grinding wheel saw blade Raw materials: The diameter of the grinding wheel used by the spring steel saw blade CNC grinding machine is 150mm, the diameter is 25mm, and the wall thickness is selected according to the tooth type and pitch of the saw blade. Grinding wheel raw material according to the type of grinding wheel saw blade material. According to experience, the particle size distribution is in the middle of 60-100, and the strength is in the middle of K-N. The main use of ceramic sintering method to manufacture the grinding wheel, but also widely used other epoxy resin and plastic bonding method to manufacture the grinding wheel. In all kinds of environments, it is very important to choose a grinding wheel with high cost performance and relatively stable balance. Grinding wheel clamp

Teach you how to choose cost-effective grinding wheel saw blade?

Release time:

2023/03/20 22:58

Second, after disconnecting the pipe, if you want to cut the mouth, when disconnecting the pipe, use a grinding wheel saw to cut the double-wall corrugated pipe, press twice, if you want to fix the damaged Showa environmental protection pipe, then cut the pipe and draw a line, please put the pipe in the grinding wheel saw clamp. Without applying too much force. If the force on the thrust sample is uniform. Please draw a rope line with the suggested pressure scissors. The force of the line and the pressure pad is uniform. In prison, the iron film and the cross section of the nozzle must be cleanly removed. There is no distortion or deformation of the nozzle cross-section, and the size of the casing cutting tube should be based on the straight

What are the uses of grinding wheel saw blades?

Release time:

2023/03/13 22:55

According to the situation of the little girl's finger being stuck, the firemen first mashed the ice cubes and applied them around the little girl's index finger. After the index finger was slightly swollen, the firemen comforted and encouraged the little girl's mood. Then, they immediately polished and cut the iron piece holding the little girl's right index finger with small grinding wheel saw, hand saw and pointed-nose pliers. In order to ensure the little girl's finger, the firemen protected and cooled her fingers. As an early enterprise in the industry to develop and realize the industrialization of diamond wire saws, the diamond grinding wheel and diamond wire series products produced by Sanchao

What are the characteristics of the grinding wheel saw blade

Release time:

2023/03/06 23:07

The opening method is correct: when cutting ampoules with grinding wheel, alcohol should be used to disinfect ampoules first and then cutting with grinding wheel. cutting with excessive force should not be used, and the cutting marks should not be too deep and long, with 1/4 of the bottleneck. The bottleneck can be broken after the application of alcohol disinfection after cutting saw, research shows that the use of spray disinfection, ampoule bottleneck glass debris greatly reduced. Among them, wet grinding wheel cutting is the cutting method of metallographic specimen. Because the high pressure cooling water is added in the cutting process, it can prevent damage due to surface overheating. And electric spark wire cutting, saw or laser cutting and other methods will lead to material

What do you know about the classification of resin cutting pieces?

Release time:

2023/03/03 20:17

Resin cutting sheet is a cutting sheet made of white corundum, brown corundum and other related materials with resin as binder. Used to cut stainless steel tubes, capillaries and glass test tubes. Thin resin cutting head with resin as adhesive, fusion of a variety of materials, carbon steel, stainless steel and other difficult to cut raw materials cutting performance is particularly evident. Dry test and wet two kinds of cutting methods, so that the cutting precision is more durable. At the same time, the selection of resin cutting piece material and hardness can greatly improve your cutting efficiency and save your production cost. Used for stainless steel pipe, wool

< 1 2 3 4 5 >

It was built in 1993. the company is located in hebei province qingxian north industrial zone, 180 kilometres from beijing, 70 kilometres from tianjin, shijiazhuang 230 kilometres...

Hebei Zhenxing Grinding Wheel Manufacturing Co., Ltd.

Address: West of 104 National Highway, North of Qingxian County, Hebei Province
Telephone: 86-18832778011 0317-4071204
Website:http://www.hbzxsl.cn/
E-mail:qu@hbzxsl.cn

License